Skip to main content

A Low Distortion Audio Pre amplifier


In an audio amplifier the quality of sound depends upon a number of factors, e.g. quality of active and passive components, circuit configuration, and layout. To an extent, the selection of components depends on the constructor’s budget. The discrete active components like transistors have been increasingly replaced by linear ICs, making the task of designer easier. With the passage of time, the general-purpose op-amps like LM741, which were being used in audio/hi-fi circuits, have become The preamplifier circuit presented here is based on a dual precision op-amp for the construction of a low distortion, high quality audio preamplifier.

Circuit diagram :

A Low Distortion Audio Pre-amplifier Circuit Diagram

A Low Distortion Audio Pre-amplifier Circuit Diagram

 

A dual op-amp OPA2604 from Burr-Brown is used for all the stages. The FET input stage op-amp was chosen in this context it is worthwile to mention another popular bi-polar architecture op-amp, the NE5534A. It has, no doubt, an exceptionally low noise figure of 4nV/ÖHz but rest of the specifications compared to OPA2604 are virtually absent in this IC. Also This IC is also capable of operating at higher voltage rails of ± 24V (max.). Also its input bias current (100 pA) is many orders lower than its bipolar counterpart’s. This ensures a multifold reduction in noise.


A channel seperation of 142 dB exists between In the circuit, buffer is essential for the proper working of the subsequent blocks. A nominal input impedance of 47k is offered by this stage which prevents overloading of the preamplifier. The tone control is a baxandall type filter circuit.The bandwidth limiter is basically a low-pass filter with an upper cut-off ceiling at the end of the useful audio spectrum. The gain at 10 kHz is approximately 17 dB. The design is essentially 3-pole type and the upper frequency is set at 25 kHz. This lSetting the unit is fairly simple. Check the power leads feeding the IC for symmetrical voltages. High quality audio output from the line output socket is to be fed as the input signal to this preamplifier. Output of the preamplifier is fed to the power a The whole circuit consumes about 10 mA when the above-mentioned ICs are used. Power supply requirements are not critical as the circuit works on 7.5V to 15V DC..

Source : electronicsforu


Labels:

Comments

Post a Comment

Popular posts from this blog

Power Amplifier with voltage regulator 4 × 50 Watt TDA8588

Power Amplifier with voltage regulator 4 × 50 Watt TDA8588    The TDA8588 is a multiple voltage regulator combined with four independent audio power amplifiers configured in bridge tied load with diagnostic capability. The output voltages of all regulators except regulators 2 and 3 can be controlled via the I2C-bus. However, regulator 3 can be set to 0 V via the I2C-bus. The output voltage of regulator 2 (microcontroller supply) and the maximum output voltage of regulator 3 (mechanical digital and microcontroller supplies) can both be either 5 V or 3.3 V depending on the type number. The maximum output voltages of both regulators are fixed to avoid any risk of damaging the microcontroller that may occur during a disturbance of the I 2C-bus. The amplifier diagnostic functions give information about output offset, load, or short-circuit. Diagnostic functions are controlled via the I2C-bus. The TDA8588 is protected against short-circuit, over-temperature, open ground and open VP connectio
Post a Comment
Read more

PIC16F887 877 programming in C Tutorial 5 LCD Interfacing

LCD Interfacing: In this tutorial i will show you how to interface 16x2 LCD with micro-controller. 16x2 means there are two rows and each row contain maximum 16 characters.  For more detail refer to the LCD datasheet, which you are using. Basic Connection: Applies 5v to pin 2 and gnd to pins 1 & 5. Use variable resistor at pin 3 to set contrast. Pins 7 to 14 are the data pins,, used to send/rec data. Pin 6 is of enable; every time when you write to lcd you should have to give high to low, to this pin. pin 4 is register select pin use to give commands like clear, home etc.   In this tutorial i will interface lcd in 4-bit instead of 8-bit, so we only required four data pins. Code: Lets write a code that will display the motor status and its direction; it will be fun!!!! Requirements: Design a motor controller circuit using l298 and display its status on lcd. LCD is connected to portb and motor controller circuit is at portd. Required two switches to change motor direction; if both ar
Post a Comment
Read more

12V to 30V DC to DC Converter circuit Diagram

 12V to +/- 30V DC to DC Converter circuit Diagram This is a DC to DC converter for car power amplifier. 12V input generates +30V and -30V output for preamp or power amplifiers. Circuit uses SG3525 IC, Mosfets and switching power supply.
Post a Comment
Read more