Clap operated Remote Control for Fans

Here is the circuit of clap-operated remote control fans is used to control not only switching properties but also control speed of fan. The main advantage of clap operated remote control for fan is, it can control up to ten-step speeds of fan where normally a fan has three to five step speeds.

Circuit description clap operated remote control for fan

This entire circuit clap operated remote control for fan is divided into four major section i.e. sound-operated trigger pulse generator, clock pulse generator, clock pulse counter and load operator.
Sound-operated trigger pulse: – The heart of this section is transistor T₁ BC148, configured as class-C amplifier mode. The MIC₁ is used to change voice signal into its corresponding electrical signal and is given to base of transistor T₁ in order to amplify and increase its intensity.
Clock pulse generator:- This section is build around timer IC NE555 and configured as monostable multivibrator. The trigger pulse generated by transistor T₁ is given to pin 2 of IC₁ and time period (T) for output high is calculated by formula.

T = 1.1RC

Clock Pulse counter:- This section is build around decade counter CD4017BC which counts the clock pulse generated by timer IC (IC₁). The output from IC₁ is given to pin 14 of IC₂. IC₂ has ten outputs, viz, o, 1, 2, 3, 4…..9. Here we use only three outputs i.e. output 1, 2 and 3 from pin 2, 4, and 7 respectively. Output 4 from pin 10 is directly connected to reset pin 15.
Load operator:- This section is build around three transistor as relay driver to operate three separate relay. Output from each pin of IC₂ is given to base of each transistor through 100Ω and LED as shown in circuit diagram. Output is taken from collector of transistor and is connected to relay. The three LEDs used to indicate gear or speed i.e. LED₁, LED₂ & LED₃ indicates gear 1, gear 2 & gear 3 respectively.

NOTE:-This circuit used to operate in 1^st speed similarly, 2^nd clap for 2^nd speed, 3^rd clap for 3^rd speed and 4^th clap to switch off the fan.

PARTS LIST

Resistors (all ¼-watt, ± 5% Carbon)

R₁ = 10 KΩ

R₂ = 1.2 MΩ

R₃ = 2.2 KΩ

R₄ = 150 KΩ

R₅ = 220 KΩ

R₆ = 10 KΩ

R₇, R₈, R₉ = 100 Ω

Capacitors

C₁, C₂ = 0.1 µF/16V

C₃ = 4.7 µF/16V

C₄ = 0.01 µF (ceramic disc)

C₅ = 1000 µF/12V

Semiconductors

IC₁ = NE555 (Timer IC)

IC₂ = CD4017BE (decade counter)

T₁ = BC148

T₂, T₃, T₄ = BEL187

D₁, D₂ = 1N4001 silicon diode

Miscellaneous

MIC₁ = Condenser microphone 34LOD

LED₁ = Green

LED₂ = yellow

LED₃ = RED

Comments

Electronic Extended Play Circuit Diagram

This is a Electronic Extended Play Circuit Diagram. A single op amp-one of four contained in the popular LM324-is operating in a variable pulse width, free-running square wave oscillator circuit, with its timed output driving two transistors that control the on/ off cycle of the tape-drive motor. The Oscillator` s positive feedback path holds the secret to the successful operation of the variable on/ off timing signal. Electronic Extended Play Circuit Diagram The two diodes and pulse width potentiometer R8 allows the setting of the on and off time, without affecting the oscillator`s operating frequency. One diode allows only the discharge current to flow through it and the section of R8 that it`s connected to. The other diode, and its portion of R8, sets the charge time for the timing capacitor, C3. Since the recorder`s speed is controlled by the precise off/on timing of the oscillator, a simple voltage-regulator circuit (Ql, R3, and D4) is included. Connecting the spe...

Power Amplifier with voltage regulator 4 × 50 Watt TDA8588

Power Amplifier with voltage regulator 4 × 50 Watt TDA8588 The TDA8588 is a multiple voltage regulator combined with four independent audio power amplifiers configured in bridge tied load with diagnostic capability. The output voltages of all regulators except regulators 2 and 3 can be controlled via the I2C-bus. However, regulator 3 can be set to 0 V via the I2C-bus. The output voltage of regulator 2 (microcontroller supply) and the maximum output voltage of regulator 3 (mechanical digital and microcontroller supplies) can both be either 5 V or 3.3 V depending on the type number. The maximum output voltages of both regulators are fixed to avoid any risk of damaging the microcontroller that may occur during a disturbance of the I 2C-bus. The amplifier diagnostic functions give information about output offset, load, or short-circuit. Diagnostic functions are controlled via the I2C-bus. The TDA8588 is protected against short-circuit, over-temperature, open ground and open VP ...

Digital Voltmeter Circuit with ICL7107

Description. The circuit given here is of a very useful and accurate digital voltmeter with LED display using the ICL7107 from Intersil. The ICL7107 is a high performance, low power, 3.5 digit analog to digital converter. The IC includes internal circuitry for seven segment decoders, display drivers, reference voltage source and a clock. The power dissipation is less than 10mW and the display stability is very high. The working of this electronic circuit is very simple. The voltage to be measured is converted into a digital equivalent by the ADC inside the IC and then this digital equivalent is decoded to the seven segment format and then displayed. The ADC used in ICL7107 is dual slope type ADC. The process taking place inside our ADC can be stated as follows. For a fixed period of time the voltage to be measured is integrated to obtain a ramp at the output of the integrator. Then a known reference voltage of opposite polarity is applied to the input of the integrator and allowed to r...

My Circuit

Search This Blog