Skip to main content

Posts

Showing posts with the label Watt

4 channel 37 Watt amplifier circuit

The HA13159 is four-channel BTL amplifier IC designed for car audio, featuring high output and low distortion, and applicable to digital audio equipment. It provides 37 W output per channel, with a 13.7 V power supply and at Max distortion. Circuit diagram: 4-channel 37 Watt amplifier circuit Datasheet for HA13159: Download

0 5 Watt power amplifier circuit with TDA1015T

This circuit is also Very simple and easy to make , simply by using the IC and 6 other components such as resistor and capacitor, you have to run this circuit. The IC uses TDA1015T , minimum voltage require 3 volt and maximum voltage required 12 volt. Power output 0,5 Watt mono , its low power amplifier. Power amplifier Schematic below : Click image to view larger If the amplifier does not work , please check : Supply voltage Components , its damaged or not. Input connected or not Output connected or not Supply voltage of each components Line PCB.

Inverter 5000 Watt PWM

This inverter uses PWM ( Pulse Width Modulator ) with type IC SG3524 . IC serves as a oscillator 50Hz, as a regulator of the desired output voltage. Input power ranging from 250W up to 5000W output and has. Following a series INVERTER 5000W with PWM (Pulse Width Modulator). Schematic Inverter 5000W with PWM (Pulse Width Modulator) Layout PCB Inverter 5000W with PWM (Pulse Width Modulator) below is the output power settings that can be issued by this inverter: DC voltage and Transformer "T2" winding recommendation: Winding Power Supply 12VDC 750W P: 24V "12-0-12" / S: 220V 1500W 24VDC P: 48V "24-0-24" / S: 220V 2250w 36VDC P: 72V "36-0-36" / S: 220V 3000w 48VDC P: 96V "48-0-48" / S: 220V 3750w 60VDC P: 120V "60-0-60" / S: 220V 4500w 72VDC P: 144V "72-0-72" / S: 220V 5250w 84VDC P: 168V "84-0-84" / S: 220V Transformer used is the transformer CT R1 serves to regulate the voltage to 220v inverter R2 serves ...

2 X 2 4 2 x 4 5 17 Watt Power Amplifier

Amplifier circuit here is all based on the ic in the gains. Three IC TA7230P, TA7236P, TA7237AP is intregated circuit (IC) which was applied to the power amplifier. Each IC has a different output, different input voltage, all IC TA7230P, TA7236P, TA7237AP is manufactured by Toshiba. TA7230P, TA7236P, TA7237AP amplifier schematic

4 x 15 Watt amplifier car audio

The HA13153A/HA13154A is high output and low distortion 4 ch BTL power IC designed for digital ca raudio. At 13.2 V to 4 Ω load, this power IC provides output power 15 W with 10% distortion. Circuit Diagram: Circuit diagram for 4 x 15 Watt amplifier car audio Datasheet for HA13153: Download

Power Amplifier with voltage regulator 4 × 50 Watt TDA8588

Power Amplifier with voltage regulator 4 × 50 Watt TDA8588    The TDA8588 is a multiple voltage regulator combined with four independent audio power amplifiers configured in bridge tied load with diagnostic capability. The output voltages of all regulators except regulators 2 and 3 can be controlled via the I2C-bus. However, regulator 3 can be set to 0 V via the I2C-bus. The output voltage of regulator 2 (microcontroller supply) and the maximum output voltage of regulator 3 (mechanical digital and microcontroller supplies) can both be either 5 V or 3.3 V depending on the type number. The maximum output voltages of both regulators are fixed to avoid any risk of damaging the microcontroller that may occur during a disturbance of the I 2C-bus. The amplifier diagnostic functions give information about output offset, load, or short-circuit. Diagnostic functions are controlled via the I2C-bus. The TDA8588 is protected against short-circuit, over-temperature, open ground and open VP ...

Super Simple 3 Watt Audio Power Amplifier

Here is the circuit diagram of superb mini audio power amplifier, That can be power with 4.5 volt dc to 18 volts dc (maximum). This amplifier is based on TDA1015, Product of NXP Semiconductors formerly PHILIPS Semiconductors. The TDA1015 is a monolithic integrated audio amplifier circuit in a 9-lead single in-line (SIL) plastic package. The device is especially designed for portable radio and recorder applications and delivers up to 4 watt in a 4 ohm load impedance. The very low applicable supply voltage of 3,6 V permits 6 V applications. Parts: R1330K R25.6K R34.7R C11uF-25V C21uF-25V C3100pF C4100nF-63V C5182pF C6224pF C7100uF-25V C8100nF-63V C910uF-25V C101KuF-25V IC1TDA1015 Applications : In-car use Your own unique application Power amplifier for audio projects For use with portable audio equipment Small but powerful multi-purpose amplifier Special features: Low current drain High output power Thermal protection High input impedance Separated preamplifier and power amplifier Limite...

60 Watt Subwoofer Amplifer Circuit

THis is very nice amplifier circuit , because High output , and voltage required is also not too large, and suitable for th subwoofer speaker.This circuit use IC TDA1102 ,  Minimum require voltage 6 volt and maximum voltage 16 volt with impedance 4 ohm . This circuit perfect those of you wear the speakers subwoofer especially in the small room , like in the car. See circuit subwoofer below :