My Circuit

The National Semiconductor LMV225 is a linear RF power meter IC in an SMD package. It can be used over the frequency range of 450 MHz to 2000 MHz and requires only four external components. The input coupling capacitor isolates the DC voltage of the IC from the input signal. The 10-k? resistor enables or disables the IC according to the DC voltage present at the input pin. If it is higher than 1.8 V, the detector is enabled and draws a current of around 5–8 mA. If the voltage on pin A1 is less than 0.8 V, the IC enters the shutdown mode and draws a current of only a few microampères. The LMV225 can be switched between the active and shutdown states using a logic-level signal if the signal is connected to the signal via the 10-kR resistor. Circuit diagram:  Linear RF Power Meter Circuit Diagram The supply voltage, which can lie between +2.7 V und +5.5 V, is filtered by a 100nF capacitor that diverts residual RF signals to ground. Finally, there is an output capacitor that forms a...

This is a simple project of Stabilized Regulated Power Supply Circuit Diagram. This circuit of power supply, is very simple and easy to built, it can be assembled on a general-purpose PCB, finding its materials is very easy and cost-small. The output voltage is stabilized and is regulated in the region from 0V until + 15V dc, with biggest provided current 1 A. The regulation becomes with the P1. The Q1 is classic power transistor and it needs to be placed on a cool rib (Heatsink), when it works continuously in the region of biggest current it gets hot. The type of transformer is standard in the market. Circuit diagram: Stabilized Power Supply Circuit Diagram Parts: P1 = 330R-Potentiometer R1 = 560R-2W C1 = 2200uF-35V C2 = 100uF-35V C3 = 10uF-25V C4 = 220uF-25V C5 = 100nF-63V D1 = 18V-1.5W Zener Q1 = 2N3055 NPN Transistor T1 = 220VAC – 18V@ 1.5A BR1 = 4x1N4007 Diode Bridge SW1 = Mains On-Off Switch Sourced By: www.circuitsstream.blogspot.com

In this amplifier circuit using IC TDA8944J as the main amplifier with dual-channel audio amplifier with 2 x 7W output power at 8 Ω impedance. And a minimum supply voltage of 9-18 Volts. In this ic contains two Bridge Tied Load or BTL amplifier. The circuit is often found in audio amplifier in a series of television, besides TDA2003, TDA2006 and so forth. PCB for a series of amplifiers using IC TDA8944J is very compatible with all other types of IC in IC TDA894X family unit , and below is a schematics.

Here I will explain about the necessary voltage and power amplifier output. The voltage should have at least approximately 9Volt 30Volt voltage and maximum voltage on the DC current. For maximum output of 2 X 2Watt with impedance 8-16 ohm. Because this amplifier circuit using ic and ic is used have the equation, so that if used different ic, then the required output voltage and also differ depending ic respectively. Part List : Resistor R1 = 1M R2 = 1M R3 = 1K R4 = 1K R5 = 100K R6 = 100K R7 = 1R R8 = 1R Capacitor C1 = 1uF C2 = 220uF C3 = 1uF C4 = 100uF C5 = 5uF C6 = 5uF C7 = 0.1uF C8 = 220uF C9 = 220uF C10 = 0.1uF IC U1 = ULN2274B , ULN2277 , ULN2278B

USB Type-C is a singular cable set out to replace a slew of other connectors by making a standard, future-proof cable. In addition to charging, the USB-C allows data transfer and video as well as connecting to Ethernet. Texas Instruments' announcement of an all-in-one USB Type-C and USB power delivery controller provides a power path that operates as a single or dual-role port which allows for many host and device power implementations. The TPS65982. The TPS65982 allows for delivery of both power and data in several alternate modes. It can be configured to support data as a downstream or upstream-facing port, or as both host and device. It also supports data rates at up to 5.4Gb/s with a standby power of 40µW - more than 50% lower than competitive offerings - to extend battery life. This is especially important in mobile devices like laptops that rely on energy maximization but demand high performance. The USB Type-C included in the new MacBook Retina. In systems requiring up ...

Using TOP269EG off-line switcher IC, (U1), in a flyback configuration can be designed a very simple high efficiency notebok laptop power adapter.TOP269EG IC has an integrated 725 V MOSFET and a multi-mode controller. It regulates the output by adjusting the MOSFET duty cycle, based on the current fed into its CONTROL pin.This laptop power adapter circuit will provide a fixed 19 volts output voltage at a maximum current of 3.5A. input voltage range is between 90 to 265VAC. Common-mode inductors L3 and L4 provide filtering on the AC input. X class capacitor C1 provides differential filtering, and resistors R1 and R2 provide safety from shock if the AC is removed, by ensuring a path for C1 to discharge. This is required by safety agencies when the capacitor value exceeds 100 nF. Bridge rectifier D1 rectifies the AC input, and bulk capacitor C2 filters the DC.

Power On Indicator Circuit diagram. Some types of electronic equipment do  not provide any indication that they are  actually on when they are switched on.  This situation can occur when the back-light of a display is switched off. In addition, the otherwise mandatory mains  power  indicator  is  not  required  with  equipment  that  consumes  less  than  10 watts. As a result, you can easily forget  to switch off such equipment. If you want  to know whether equipment is still drawing power from the mains, or if you want  to have an indication that the equipment  is switched on without having to modify the equipment, this circuit provides a solution.  One way to detect AC power current and  generate a reasonably constant voltage  independent of the load is to connect a  string of diodes wired in reverse parallel in series with one of the AC supply  leads. Here we sele...

                                           This is the circuit diagram of 5V DC regulated power supply which featured with short circuit protection system. There are 2 kind of output that are regulated 5V DC with short circuit protection and without circuit protection. The main circuit is protected from any damage due to short-circuit in the additional power supply circuit by cutting off the derived supply voltage. The derived supply voltage restores automatically when shorting is removed. An indicator LED is utilized to show whether short-circuit exists or not. Power Supply Block: This circuit works just like the ordinary DC power supply adapter, in the main power supply circuit, 230V AC from main home electric source is stepped down by transformer X1 (230V AC primary to 0-9V, 3...

HANDY 0-12V DC POWER SUPPLY ELECTRONIC DIAGRAM For heat protection, heat sink is needed for the BD679 transistor. It is because it will be over tempered when works more than 200mA. FEATURES: 0v to 12 volt output: - 700mA with M 2155 - 1.4amp with M 2156 - 1A with 16v AC 1.5 amp plug pack

Useful for electronics hobbyists, this linear workbench power supply converts a high input voltage (12V) from the SMPS of a PC into low output voltage (1.25 to 9 volts). An adjustable three-pin voltage regulator chip LM317T (IC1) is used here to provide the required voltages. The LM317T regulator, in TO-220 pack, can handle current of up to 1 amp in practice. Fig. 1 shows the circuit of the desktop power supply. Regulator IC LM317T is arranged in its standard application. Diode D1 guards against polarity reversal and capacitor C1 is an additional buffer. The green LED (LED1) indicates the status of the power input. Diode D2 prevents the output voltage from rising above the input voltage when a capacitive or inductive load is connected at the output. Similarly, capacitor C3 suppresses any residual ripple. Circuit diagram : Fig.1: Desktop Power Supply Circuit Diagram Connect a standard digital voltmeter in parallel with the output leads to accurately set the desired voltage with th...

This is stereo audio amplifier with based on ICTDA2824S , Minimum voltage require 3 volts and maximum voltage 17 volts . Maximum output power 2 X 2 Watt , its low power amplifier. Output impedance  4 ohm. see schematic audio below :

Women might say that they will never be able to have enough handbags and shoes (generally speaking), while men might never get enough of their power tools and hardware toys, and kids with their video games, but I am quite sure that something most of us will be able to agree on would be this – you can never have enough power outlets around, considering the rather large number of gadgets that we carry around with us these days. Smartphones, tablets, digital cameras, smart watches, the list goes on and on, and Thinkgeek intends to help you out with the $34.99 Smart AC Automotive Power Strip. The Smart AC Automotive Power Strip will be able to juice up just about all things, where this inverter plugs into your cigarette lighter socket. It will come with a couple of USB power ports and two AC outlets, and fret not about it melting down or catching fire, since the safety features which have been thrown into the mix include over-voltage, overload, short-circuit, high-temperature protection, a...

Many modern electronic devices and micro-controller based circuits need a 5 V or 3.3 V power  supply. It is important  that  these voltages are constant and so a regulator of some kind is essential, including in battery powered devices. The simplest approach is to select a (perhaps rechargeable) battery whose voltage is rather higher than that required by the circuit and use an ordinary  linear voltage regulator. Unfortunately this solution is rather wasteful of precious energy and space: for a 5 V circuit at least six NiCd or NiMH cells would be required. Both these disadvantages can be tackled using a little modern electronics. A good way to minimise energy losses is to use a switching regulator, and if we use a regulator with a step-up topology then we can simultaneously reduce the number of cells needed to power the circuit. Fortunately it is not too difficult to design a step-up converter suitable for use in portable equipment as the semi-conductor manufacturers...

This amplifier circuit using ic BA534 as a main amplifier, manufactured by ROHM ic, and packaged in SIP1-8. This amplifier circuit has a maximum output of 2.3 Watts with 4 Ohm impedance. Frequency response is between 30Hz to 18KHz. For the voltage needed at least 9 Volt and 13 Volt maximum. For a list of components can be seen below. Part List : R1 = 50K trim R2 = 33K R3 = 68R C1 = 2.2uF C2 = 220uF C3 = 100uF C4 = 47uF C5 = 470uF C6 = 100uF C7 = 47uF C8 = 100n U1 = BA534

This IC is a hybrid designed to be used  in 150 W 3ch class AB  audio power amplifier. 150W+150W+150W audio power amplifier

This circuit was originally designed to power a motorcycle intercom from the vehicle supply system. This type of intercom, which is used for communication between driver and passenger, generally requires quite a bit of power. In order to improve intelligibility there is often elaborate filtering and a compander is sometimes used as well. The disadvantage is that a battery doesn’t last very long. You could use rechargeable batteries, of course, but that is often rather laborious. It seems much more obvious to use the motorcycle power supply instead. A 9-V converter for such an application has to meet a few special requirements. 9V Battery Replacement Power Supply Circuit Diagram For one, it has to prevent interference from, for example, the ignition system reaching the attached circuit. It is also preferable that the entire circuit fits in the 9-V battery compartment. This circuit meets these requirements quite successfully and the design has nonetheless remained fairly simple. In the s...

This time I will share a circuit of schematis power amplifier with LM380 IC that has similarities with LM384. Enough with just a few components you have to make this power amplifier circuit . All components with relatively low prices and making a fairly easy. For this amplifier output power has 3W with 4 ohm impedance. Indeed , this amplifier has the output is quite low and certainly will not be maximal if it works on the speakers with high power. Component List : Resistor R1______________47K R2______________2.7R 2W Capacitor C1______________10uF C2______________470uF C3______________100n C4______________100n IC IC1_____________LM380 , LM384

Many times the hobbyist desires to have a simple, dual power supply for a project. Existing power supplies may be large either in power output or physical size. a simple Dual Power Supply is necessary.For most non-critical applications the best & simplest choice for a voltage regulator is the 3-terminal type.The three terminals are input, ground & output. The 78xx & 79xx series can provide up to 1A load current & it have on chip circuitry to prevent damage in the event of over heating or excessive current. That is, the chip basically shuts down than blowing out. These regulators are cheap, simple to make use of, & they make it practical to design a method with plenty of P C Bs in which an unregulated supply is brought in & regulation is done locally on each circuit board. This Dual Power Supply project provides a dual power supply. With the appropriate choice of transformer & 3-terminal voltage regulator pairs you can basically build a tiny power supply deli...

Dayton Audio's versitile APA150 can relinquish 75 watts into 2 channels, before 150 watts into 8 ohms while frozen to passage-mono mode. A built-fashionable, switchable low-pass filter makes this a countless subwoofer amp, and chock-a-block range line-level outputs allow designed for bi-amp configurations. Technical Details : close to clamor-released fan process pro approach handle applications silky enlightened design looks useful in vogue every audio practice sky-scraping current, discrete output transistors with the purpose of run cool and serene adaptable 50-150 Hz low pass crossover gives you the area control you need

What is power? Power is the rate of using or supplying energy: Power =   Energy       Power is measured in watts (W) Energy is measured in joules (J) Time is measured in seconds (s)  Time Electronics is mostly concerned with small quantities of power, so the power is often measured in milliwatts (mW), 1mW = 0.001W. For example an LED uses about 40mW and a bleeper uses about 100mW, even a lamp such as a torch bulb only uses about 1W. The typical power used in mains electrical circuits is much larger, so this power may be measured in kilowatts (kW), 1kW = 1000W. For example a typical mains lamp uses 60W and a kettle uses about 3kW. Calculating power using current and voltage There are three ways of writing an equation for power, current and voltage: Power = Current × Voltage   so    P = I × V  or  I =   P  V  or  V =   P  I where: P = power in watts (W) V = vol...