Type and function of subwoofer speaker box

Know Your Types of box type subwoofer

Performance subwoofer to produce low bass sound and also solid course supported by a subwoofer enclosure or box. Subwoofer box in the car usually has a different size, it is adjusted to the recommendations of the technical data from these subwoofers. However, each audio installer, have different styles in a box design.

If all this time, we only know when the box was just the type that's all, it did not. Box consists of various types and models. Design, size (dimensions) and a subwoofer box models are usually clearly taken into account at the time of manufacture, even carefully designed too often acted the Installer. Clearly, each type of box has a value of strengths and weaknesses, all models of boxes, if applied correctly, clearly gives a very maximum performance subwoofer.

Following this, the types of subwoofer box that is often applied in car audio:

If you want us to categorize the type of subwoofer box can be divided according to several orders of more detail:

• Second Order / Infinite Baffle / Free Air

• Typical Rear Deck Installation / Infinite Baffle / Free

• Back Seat Installation

• Small Deck Installation

• Second Order / Acoustic Suspension / Sealed enclosures

• Sealed

• isobaric - Sealed

• isobaric - Sealed (Compound Loading)

• isobaric - Sealed (Back to Back)

• isobaric - Sealed (Planar Loading)

• Fourth Order / Bass Reflex & bandpass enclosures

• Fourth Order / Bass Reflex

• isobaric - Bass Reflex

• isobaric - Bass Reflex (Compound Loading)

• Bass Reflex - Passive Radiator

• isobaric Bass Reflex - Passive Radiator

• Single Reflex - Band Pass

• Single Reflex isobaric bandpass

• Three Chamber Single Reflex bandpass

• Three Chamber Single Reflex isobaric bandpass

• Sixth Order enclosures

• Quasi Sixth Order Series-Tuned bandpass

• isobaric Quasi Sixth Order Series-Tuned bandpass

• Dual reflex bandpass

• Dual Reflex isobaric bandpass

• Three Chamber Dual Reflex bandpass

• Three Chamber Dual Reflex isobaric bandpass

• Eighth Order enclosures

• Quasi Eighth Order Series-Tuned Dual Reflex bandpass

• Quasi isobaric Eighth Order Series-Tuned Dual Reflex bandpass

• Eighth Order Triple Reflex bandpass

• Eighth Order Triple Reflex isobaric bandpass

Comments

Electronic Extended Play Circuit Diagram

This is a Electronic Extended Play Circuit Diagram. A single op amp-one of four contained in the popular LM324-is operating in a variable pulse width, free-running square wave oscillator circuit, with its timed output driving two transistors that control the on/ off cycle of the tape-drive motor. The Oscillator` s positive feedback path holds the secret to the successful operation of the variable on/ off timing signal. Electronic Extended Play Circuit Diagram The two diodes and pulse width potentiometer R8 allows the setting of the on and off time, without affecting the oscillator`s operating frequency. One diode allows only the discharge current to flow through it and the section of R8 that it`s connected to. The other diode, and its portion of R8, sets the charge time for the timing capacitor, C3. Since the recorder`s speed is controlled by the precise off/on timing of the oscillator, a simple voltage-regulator circuit (Ql, R3, and D4) is included. Connecting the spe...

Power Amplifier with voltage regulator 4 × 50 Watt TDA8588

Power Amplifier with voltage regulator 4 × 50 Watt TDA8588 The TDA8588 is a multiple voltage regulator combined with four independent audio power amplifiers configured in bridge tied load with diagnostic capability. The output voltages of all regulators except regulators 2 and 3 can be controlled via the I2C-bus. However, regulator 3 can be set to 0 V via the I2C-bus. The output voltage of regulator 2 (microcontroller supply) and the maximum output voltage of regulator 3 (mechanical digital and microcontroller supplies) can both be either 5 V or 3.3 V depending on the type number. The maximum output voltages of both regulators are fixed to avoid any risk of damaging the microcontroller that may occur during a disturbance of the I 2C-bus. The amplifier diagnostic functions give information about output offset, load, or short-circuit. Diagnostic functions are controlled via the I2C-bus. The TDA8588 is protected against short-circuit, over-temperature, open ground and open VP ...

Siemens LOGO PLC Ladder Programming Steps

Siemens LOGO PLC Ladder Programming Steps Following are Step by Step instruction to Program Siemens Logo PLC Siemens Logo PLC Click on “ Siemens LOGO ” Click on “ siemens rse ” Click on “ StartLOGOComfor t” Wait… You will find the work pad where you have to write FBD programme Use “menus” given at the top and bottom to develop a FBD programme. Find Tools toolbar, Standard toolbar, Menu bar and Status bar. Entering a New program : Click on “ File ” “ New ” Create a program using Toolbars and Function blocks (Constants, General and Special functions) • You can then place any of those functions on the drawing board simply by clicking on the drawing board in the desired position. The function on the extreme left is selected by default but you can select any of the others by clicking them with the mouse. • It is not necessary to position the objects precisely at this point. • To ...

My Circuit

Search This Blog