Skip to main content

Spring Reverb Stomp Box Stage Center Reverb


Stage Center Reverb Bill of Materials

Resistor ((1/4 watt rating)

2 - 4.7k
1 - 10k
1 - 22k
1 - 33k
1 - 47k
1 - 470k
1 - 1M
1 - 2.2M


Pots
2 - 50k log can be linear or log (audio) taper.

Capacitors (minimum 16 volt rating)
1 - 220pF
1 - 0.01uF
2 - 0.02uF
3 - 0.22uF
2 - 39uF

Op Amp
1 - TL074


Other

Reverb Springs - Input Impedance of 310 Ohms (Accutronics 4DB2C1D)
Reverb Springs Bag (optional)

2 - cables with RCA jacks on both ends. These are used to connect the reverb springs to the circuit.

1 - 3PDT or DPDT heavy duty foot switch
2 - 1N4001 diodes
1 - 14 pin op amp socket (optional)
1 - Stereo Quarter inch Jack (input)
1 - Mono quarter inch jacks (output)
2 - RCA female jacks
2 - 9v battery snaps & holder and/or DC jack(s)
Copper-clad board, etchant, 24 gauge stranded wire
Enclosure


Labels:

Comments

Post a Comment

Popular posts from this blog

Mantis 9 1 CNC Mill

The Mantis 9.1 design is a radical departure from version 8 and earlier. Most notably, the part count has been almost halved! The current design has 13 parts, all of which can be made with a handsaw and a drill press. Also, I’ve traded away my alignment free exactly-constrained design for extra stiffness. Several unsuccessful attempts to eradicate the last of the slop in the Z axis on version 8 lead me back to the world of over-constrained parallel rods. My previous attempts at an over-constrained design (versions 1-5) all failed because I was unable to make the rods sufficiently parallel to avoid jamming. What to do? [ ]
Post a Comment
Read more

25 Watt Audio Amplifier Circuits Diagram

25 Watt Audio Amplifier Circuits Diagram Parts: R1 ,R4 _________47K   1/4W Resistors R2____________ 4K7   1 /4W Resistor R3____________ 1K5   1 /4W Resistor R5__________390R    1/4W Resistor R6__________470R    1/4W Resistor R7___________33K    1/4W Resistor R8__________150K    1/4W Resistor R9___________15K    1/4W Resistor R10__________27R    1/4W Resistor R11_________500R    1/2W Trimmer Cermet R12 ,R13,R16 __10R    1/4W Resistors R14 ,R15 _____220R    1/4W Resistors R17___________8R2     2W Resistor R18____________R22    4W Resistor ( wirewound )   C1___________ 470nF   63V Polyester Capacitor C2___________ 330pF   63V Polystyrene Capacitor C3 ,C5 ________470µF   63V Electrolytic Capacitors C4 ,C6,C8,C11 _100nF   63V Polyester Capacitors C7___________100µ F   25V Electrolytic Capacitor C9____________ 10pF   63V Polys...
Post a Comment
Read more

Electronic Extended Play Circuit Diagram

This is a Electronic Extended Play Circuit Diagram. A single op amp-one of four contained in the popular LM324-is operating in a variable pulse width, free-running square wave oscillator circuit, with its timed output driving two transistors that control the on/ off cycle of the tape-drive motor. The Oscillator` s positive feedback path holds the secret to the successful operation of the variable on/ off timing signal.   Electronic Extended Play Circuit Diagram The two diodes and pulse width potentiometer R8 allows the setting of the on and off time, without affecting the oscillator`s operating frequency. One diode allows only the discharge current to flow through it and the section of R8 that it`s connected to. The other diode, and its portion of R8, sets the charge time for the timing capacitor, C3. Since the recorder`s speed is controlled by the precise off/on timing of the oscillator, a simple voltage-regulator circuit (Ql, R3, and D4) is included.  Connecting the spe...
Post a Comment
Read more